Refinishing means repainting a car in its own color to bring the finish back after damage, sun or age. It sounds simple, and the spraying is the quick part. The judgment is in deciding how much of the car needs it, and the quality is in the work done underneath. This guide follows the questions in the order you will meet them, for drivers in New York City, Westchester and Long Island.
How factory paint is built, and why it fails
Almost every modern car leaves the factory with the same stack of layers. A corrosion coating on the metal, then primer, then a base coat that carries the color, then a clear coat on top. The clear does most of the work: it gives the gloss and takes the sun, the salt and the scratches so the color does not have to.
Paint fails when that top layer wears through or loses its grip. Ultraviolet light slowly breaks the clear coat down, which is why fading and peeling almost always start on the roof, hood and trunk. Stone chips let water reach the metal and rust starts underneath. Scratches and keying cut through the clear into the color. Old resprays done over poor prep can let go years later. Each of these shows up differently, and each needs a different fix.
Reading your paint: polish, touch up or refinish
Before anyone talks about repainting, it helps to know which of these your car needs.
- Dull but intact. The paint has lost its shine but the clear is still there and smooth. A polish and protection can often bring it back for a while.
- Light swirls and fine scratches. Marks that sit in the clear coat and do not catch a fingernail can usually be polished out.
- Small chips. A handful of fresh stone chips can be touched up before rust starts, though touch up never looks factory smooth close up.
- Deep scratches. Anything that catches a fingernail or shows another color underneath has gone into the paint. That panel needs refinishing.
- Peeling, white or chalky clear. Once the clear is lifting or bleaching, polishing cannot save it. The panel has to be sanded down and refinished.
- Bubbles or cracks. Usually moisture, rust or a failing old repair underneath. The paint has to come off to find out how far it goes.
The step from polish to refinish is the important one. Polishing a failing clear coat thins it further, and touch up will not stick to an edge that is already lifting.
Paint warning signs to look for
Walk around the car in daylight. If you find any of these, the paint is past what a polish can do.
A papery edge
Clear coat lifting like a thin sheet of plastic, often on the roof or hood.
Patches that look dusty
White or chalky color that does not wash off, most obvious on dark cars.
Two shades on one car
The top surfaces faded while the doors and sides still look darker.
Orange at the chips
Rust showing at the edge of stone chips on the hood or front bumper.
A scratch you can feel
A fingernail catches in it, or a different color shows at the bottom.
Blisters or crazing
Small bubbles or a fine cracked pattern, often over an earlier repair.
One panel or the whole car
Most refinishing is panel work. A keyed door, a scraped bumper or a hood covered in chips can be refinished on its own, with the color blended into the panels beside it so the change does not show. That blending is its own skill, paint color matching, because the rest of the car has faded a little since it was new and the fresh paint has to match the car as it is now, not the code on the door sticker.
A full refinish makes sense when the paint is going all over: clear coat failing on several panels at once, fading that differs from top to bottom, or years of chips and patched repairs. Refinishing panel by panel on a car like that can leave a patchwork, and one even finish often looks better. How much it costs to have a car sanded and painted explains how that choice, and others, change the size of the job.
Prep is most of the job
The color is what you see, but the work underneath decides how long it lasts. A proper refinish usually goes like this:
- Strip or sand back. Failing paint is sanded down to a sound layer, sometimes to bare metal, until nothing loose is left.
- Repair the surface. Dents are fixed, rust is cut out or treated, and chips are feathered smooth so their edges do not show through.
- Clean. Grease, wax and sanding dust come off, because paint will not grip over them.
- Prime. Primer seals the bare spots and levels fine marks, then it is sanded smooth again.
Skip any of that and the new paint will peel, bubble or show the old damage through it, sometimes within a season or two. When you compare quotes, the biggest difference between them is almost always here.
Inside a proper refinish
The stops a refinished panel passes through on its way back to the original color.
Assess
Each panel checked to see how deep the damage goes and what has to come off.
Take apart
Trim, handles and lights removed or carefully masked, depending on the job.
Sand and repair
Failing paint removed, dents fixed, rust treated, chips feathered smooth.
Prime
Primer laid down to seal and level, then sanded smooth.
Base and clear
Color tinted to the car and blended into its neighbors, then clear coat over it.
Finish
Light wet sanding and polishing where needed, then trim back on.
Spraying, blending and the finish
Paint goes on in a booth, which keeps out dust and controls the air so the coats dry evenly. The base color is sprayed in thin coats, tinted to match the car's paint as it is today. Clear coat follows, usually in more than one coat, to build up the gloss and the protection.
Blending is what makes a panel repair invisible. Rather than stopping the new color at the edge of the panel, the painter fades it into the next panel so the eye cannot find a line. Clear coat then goes over the whole area.
After drying, some paint jobs are lightly wet sanded and polished to take out texture and any dust caught in the clear. That step is where a respray goes from good to very good, and it is one of the things a low cost respray usually leaves out.
Is it worth repainting?
It depends on the car and your plans. Fixing paint damage early protects the metal, and rust that starts under a chip only gets more expensive to deal with. On a car you plan to keep, a sound refinish can add years of good looks. On a car worth little, or one you are about to sell, a full respray may not pay back, and panel work on the worst areas can be the better call. Whether it is worth having a car repainted weighs it up honestly.
If the paint was damaged by something your policy covers, such as a collision or vandalism, refinishing those panels is normally part of the claim, including blending into the panels next to them. Paint that wore out from sun and age is usually treated as maintenance. Our insurance claims page explains how a claim works from the shop's side.
If what you really want is a different color, that is not a refinish. It is a custom paint job, and it is planned quite differently.
Checking the work and caring for it
Look at a fresh refinish outside, in daylight, from a few angles:
- Color. The panel should match its neighbors from the front, the side and at an angle.
- Texture. The gloss should look like the rest of the car, without heavy orange peel.
- Runs, dust and dry patches. No sags in the clear, no specks trapped in it, no dull spots.
- Edges. No paint on rubber seals, glass or trim, and no tape lines.
- Jambs and openings. If they were part of the job, they should be painted cleanly too.
New paint needs time to cure. Wash it gently by hand at first, skip automatic brush washes, and ask the shop how long to wait before waxing or coating it. Clean off bird droppings, sap and fuel quickly, and touch up stone chips early, before water gets in.
Before you repaint,get the straight answer.
Each question has its own page with a short answer first and the detail underneath.
Getting your paint looked at
If your paint is peeling, fading or chipped, the first step is a look in good light. Our car painting and refinishing page explains how we handle the job, with a free estimate before any work starts. The shop is at 99-49 66th Ave in Forest Hills, Queens, open 24 hours. Call or send us the details.
Paint giving up? Call for a free look.
646-347-5520Open 24 hours.
Get a Free Estimate