A custom paint job is a design project that happens to involve a spray gun. The sanding and spraying matter, but most of what decides whether you love the result happens earlier: which color, which finish, how far the change reaches and what the car underneath is like. This guide is for anyone thinking about a new look, written for drivers in New York City, Westchester and Long Island but true almost anywhere.
Custom paint, refinishing or color matching
Three kinds of paint work get mixed up all the time, and they are planned very differently.
- Custom paint changes the look on purpose. A new color, two tones, stripes, a special finish or painted details. The goal is something the car never had.
- Painting and refinishing puts the car's own finish back after damage, sun or age. The goal is the original color, looking new again.
- Color matching is the step inside a repair that makes a new panel blend with the old ones around it. The goal is that nobody can see where the repair is.
If your paint is peeling and you just want it to look right again, you are describing a refinish, and the car painting and refinishing page is the better starting point. If one panel was repaired and looks a shade off, that is a paint color matching question. Everything below is for the driver who wants something new.
Choosing the color
Start with the color, but think about how it is made, not just what it is called. Car paint comes in a few broad families, and each behaves differently on a real car.
- Solid colors. One flat pigment with no sparkle. Easy to understand, but dark solids such as black show every ripple and scratch.
- Metallics. Fine flakes of aluminum in the color that catch the light. They hide small flaws well but have to be sprayed evenly or they look blotchy.
- Pearls and tri coats. A base color, a translucent pearl layer and clear on top. The depth is lovely, and the result depends heavily on how many coats of the middle layer go on.
- Candies. A tinted, see through layer over a bright base. Rich and deep, and among the least forgiving to spray.
- Matte and satin. Any of the above with a clear that does not shine. Striking, but it changes how the car has to be cared for.
How a color looks also depends on the car. A sharp crease shows off a metallic. A long, flat door shows every wave in a dark solid. Some colors are much harder to lay down well than others, and what the hardest color to paint a car is explains which ones and why.
Seeing the color for real
A color on a phone screen, a brochure or a small chip under shop lights is not the color you will get. Light, the angle you stand at and the surface it sits on all change it.
Ask for a spray out card or a test panel sprayed in the actual paint, with the actual clear. Look at it outside, in full sun and in shade, and again at dusk. Hold it next to the car's trim, wheels and interior, because those are not changing. For tri coats and candies, the test panel should be built with the same number of coats the car will get, since that number changes the shade.
Take a photo of the card in daylight and keep it. Weeks from now, when you are deciding about stripes or a second tone, it is the most honest reference you will have.
Decisions to settle before the estimate
Each of these changes how much work the job involves. Agree them up front and make sure they are written on the estimate.
The exact color and finish
Seen on a test card in daylight, with the clear that will go on the car.
How deep the change goes
Outside only, or door jambs, the trunk opening and under the hood too.
What comes off the car
Trim, handles, lights, badges and sometimes glass, versus masking around them.
Body work first
Dents, rust and old repairs to fix before any color goes on.
Extras and details
Two tones, stripes, graphics, painted calipers, mirrors or trim.
A record of the paint
The exact products and coat count, written down for any future repair.
How far the new color reaches
This is the decision that changes the job most, and it is easy to underestimate.
Painting only the outside panels leaves the old color in the door jambs, the inside edge of the hood, the trunk opening and under the fuel door. You see it every time you open a door, and so does anyone looking at the car to buy it. A full color change takes the new color into those openings, which means more parts removed, more masking and more surfaces to prep.
The same goes for trim. Taping around handles, lights and seals is quicker, but the edge of the tape is where new paint most often lifts or shows a line later. Taking parts off lets the color wrap around every edge the way it did from the factory. Neither choice is wrong. What matters is that you choose it knowingly and see it on the estimate.
The car underneath the color
New paint is only as good as what it sits on. Every ding, ripple and old repair under a glossy new color will show, often more clearly than before, so body work comes first. Rust has to be cut out or treated, not painted over, or it will push the new finish off from below. A car with serious rust or tired panels may need auto body restoration before it is ready for a new color at all.
The old paint matters too. If it is cracked, peeling or has been resprayed badly in the past, laying new paint over it is asking for trouble. It usually has to be sanded back to a sound layer, sometimes to bare metal. If you have ever wondered what causes car paint to peel, most of the answers are about what happened, or did not happen, underneath.
How a custom finish is built
A custom finish goes on in layers, and each one has a job. The order is roughly the same whatever the color.
From bare panel to new color
The layers of a custom paint job, from the bottom up. Skipping or rushing any one of them shows up later.
Sound surface
Old paint sanded back, dents fixed, rust dealt with, panels cleaned of grease and dust.
Primer
Grips the metal or old paint, fills fine sanding marks and is sanded smooth again.
Sealer
An even, uniform layer so the new color looks the same on every panel.
Base color
The color itself, built up in thin, even coats.
Mid coat or graphics
Pearl or candy layers, second tones and stripes, masked and sprayed in turn.
Clear coat
Gloss, satin or matte, protecting everything under it from sun, salt and scratches.
Two tones and stripes add masking between layers, and the lines usually follow a body crease so the split looks deliberate. Graphics sprayed under the clear coat are protected by it, which is why they last longer than anything stuck on top.
Paperwork, insurance and resale
A new color has some practical loose ends.
- The DMV. In New York the color is recorded on the registration, and owners are expected to update it after a color change. Check the current rules with the DMV.
- Your insurer. Tell them about the change. Insurance pays to repair damage, so a custom job is normally paid for by you. If the car is already in for covered damage, you may be able to pay the difference to go custom on those panels while the car is apart.
- Resale. A custom color is personal. It can make a car stand out or narrow the number of buyers. If you plan to sell soon, that is worth weighing.
- Future repairs. Keep the record of products and coats. Matching a tri coat or candy panel after a scrape is far easier when the shop knows exactly how it was built.
Living with a custom finish
Fresh paint takes time to cure fully, so wash it gently by hand at first and ask the shop how long to wait before waxing or sealing it. Automatic brush washes are hard on any finish and especially hard on new or dark paint.
Matte and satin finishes need their own routine. They should not be polished or waxed like gloss paint, because that leaves shiny patches. Use products made for matte paint, and clean off bird droppings, tree sap and fuel spills quickly, since they can mark the surface for good. Stone chips on any custom color are best touched up early, before moisture gets under the edge and the paint starts to lift.
Straight answersbefore you pick a color.
Each question has its own page with a short answer first and the detail underneath.
Planning your own custom job
If you have a color in mind, the next step is a conversation. Our custom paint job page explains how we plan and quote the work, with a free estimate before any work starts. The shop is at 99-49 66th Ave in Forest Hills, Queens, open 24 hours, and you can call or send us the details to start.
Thinking about a new color? Call to talk it through.
646-347-5520Open 24 hours.
Get a Free Estimate